Rani, Joseph(John Wiley & Sons, Inc., February 16, 1999)
[+]
[-]
Abstract:
Microcellular (MC) soles based on polybutadiene (BR) and low-density
polyethylene (LDPE) blends for low-temperature applications were developed. A part of
BR in BR-LDPE blend was replaced by natural rubber (NR) for property improvement.
The BR-NR-LDPE blend-based MC sole shows good technical properties. Sulphur
curing and DCP curing were tried in BR-LDPE and NR-BR-LDPE blends. Study
shows that sulphur-cured MC sheets possess better technical properties than DCPcured
MC sheets. 90/10 BR-LDPE and 60/30/10 BR-NR-LDPE blend combinations are
found to be suitable for low-temperature applications.
In this article, we report the preparation of
conducting natural rubber (NR) with polyaniline (Pani). NR
was made into a conductive material by the compounding
of NR with Pani in powder form. NR latex was made into a
conductive material by the in situ polymerization of aniline
in the presence of NR latex. Different compositions of Pani-
NR semi-interpenetrating networks were prepared, and the
dielectric properties of all of the samples were determined
in microwave frequencies. The cavity perturbation techpique was used for this study. A HP8510 vector network analyzer
with a rectangular cavity resonator was used for this
study. S bands 2-4 GHz in frequency were used. Thermal
studies were also carried out with thermogravimetric analysis
and differential scanning calorimetry.
In this article, we report the preparation of
conducting natural rubber (NR) with polyaniline (Pani). NR
was made into a conductive material by the compounding
of NR with Pani in powder form. NR latex was made into a
conductive material by the in situ polymerization of aniline
in the presence of NR latex. Different compositions of Pani-
NR semi-interpenetrating networks were prepared, and the
dielectric properties of all of the samples were determined
in microwave frequencies. The cavity perturbation techpique was used for this study. A HP8510 vector network analyzer
with a rectangular cavity resonator was used for this
study. S bands 2-4 GHz in frequency were used. Thermal
studies were also carried out with thermogravimetric analysis
and differential scanning calorimetry.
Rani, Joseph(Hutig & Wepf Verlag,Basel, October 5, 1987)
[+]
[-]
Abstract:
Compounding of styrene-butadiene copolymer/polybutadiene , natural rubber/
ethylene-propylene-diene terpolymer and natural rubber/butadiene-acrylonitrile copolymer
blends was done in three different ways and their curing behaviour and the
tensile properties of the es are compared.
Isora fibre-reinforced natural rubber (NR) composites were cured at 80, 100, 120 and
150°C using a low temperature curing accelerator system. Composites were also prepared using a
conventional accelerator system and cured at 150°C. The swelling behavior of these composites at
varying fibre loadings was studied in toluene and hexane. Results show that the uptake of solvent
and volume fraction of rubber due to swelling was lower for the low temperature cured vulcanizates
which is an indication of the better fibre/rubber adhesion. The uptake of aromatic solvent was higher
than that of aliphatic solvent, for all the composites. As the fibre content increased, the solvent
uptake decreased, due to the superior solvent resistance of the fibre and good fibre-rubber interactions.
The bonding agent improved the swelling resistance of the composites due to the strong interfacial
adhesion. Due to the improved adhesion between the fibre and rubber, the ratio of the change in
volume fraction of rubber due to swelling to the volume fraction of rubber in the dry sample (V,) was
found to decrease in the presence of bonding agent. At a fixed fibre loading, the alkali treated fibre
composite showed a lower percentage swelling than untreated one for both systems showing superior
rubber-fibre interactions.
Rani, Joseph(Wiley InterScience, February 18, 2006)
[+]
[-]
Abstract:
In this paper we report the preparation and
dielectric properties of poly o-toluidine:poly vinyl chloride
composites in pellet and film forms. The composites were
prepared using ammonium persulfate initiator and HCl
dopant. The characterization is done by TGA and DSC. The
dielectric properties including dielectric loss, conductivity,
dielectric constant, dielectric heating coefficient, absorption
coefficient, and penetration depth were studied in the
microwave field. An HP8510 vector network analyzer with
rectangular cavity resonator was used for the study. Sbands (2-4 GHz), C band (5-8 GHz), and X band (8-12
GHz) frequencies were used in the microwave field. Comparisons
between the pellet and film forms of composites
were also included. The result shows that the dielectric
properties in the microwave field are dependent on the frequency
and on the method of preparation.
Rani, Joseph(Wiley lnterScience, September 4, 2006)
[+]
[-]
Abstract:
The latex industry has expanded over the
years to meet the world demands for gloves, condoms,
latex thread etc. Because of the strict specifications for
the products and the unstable nature of the latex, as
high as 15%, of the final latex products are rejected.
Since waste latex rubber (WLR) represents a source of
high quality rubber hydrocarbon, it is a potential candidate
for generating reclaimed rubber of superior quality.
Two types of WLR with different amounts of polysulfidic
bridges are used in these experiments, which are
reclaimed with variation of the concentration of the
reclaiming agents, the reclamation temperature and time,
Di phenyldisultide, 2-aminophenyldisulfide and 2,2'-dibenzamidodiphenyldisulfide
(DBADPDS) are used as reclaiming
agents, and the effect of diphenyldisulfides (DPDS)
with different substituents, on the reclamation efficiency of WLR is investigated. A kinetic study of the reclamation
reaction with the three reclaiming agents is done.
The reaction rates and activation energies are calculated
and compared with literature values. The comparative
study of the three different reclaiming agents shows that
(DBADPDS) is able to break the crosslinks at temperature
levels 20'C below the temperature levels normally
used with DPDS. Another advantage of this reclaiming
agent is the reduced smell during the reclamation process
and of the final reclaims, one of the most important
shortcomings of other disulfides used for this purpose.
Rani, Joseph(John Wiley & Sons, Inc., June 21, 2001)
[+]
[-]
Abstract:
ABSTRACT: Polyaniline was synthesized by using ammonium persulfate initiator in the
presence of 1M HC1. It was dried under different drying conditions like room temperature
drying (for 48 h), oven drying (at 50-60°C for 8 h under a vacuum), and vacuum
drying (at room temperature for 16 h). The conductivities of these samples were
measured at microwave frequencies. These samples were also pelletized and the
measurements were repeated. The cavity perturbation technique was used for the
study.
Rani, Joseph(OPA (Overseas Publishers Association) N.V., July 23, 1997)
[+]
[-]
Abstract:
Selected grades of low density polyethylene (LDPE) polystyrene (PS) were extruded in a
laboratory extruder by varying the feeding rate at different revolutions per minute and
temperatures. The mechanical properties of the extruded plastic sheets were determined.
LDPE shows a marked variation in mechanical properties with feeding rate while PS
shows a marginal change in mechanical properties with feeding rate. However, for both
plastics there is a particular feeding rate in the starved region which results in maximum
mechanical properties.
Rani, Joseph(Wiley InterScience, December 13, 2004)
[+]
[-]
Abstract:
Prevulcanized natural rubber latex was prepared
by the heating of the latex compound at 55°C for
different periods of time (2, 4, 6, 8, and 10 h). The changes in
the colloidal stability and physical properties were evaluated
during the course of prevulcanization. The prevulcanized
latex compounds were stored for 300 days, and the
properties were monitored at different storage intervals (0,
20, 40, 60, 120, 180, 240, and 300 days). During prevulcanization,
the mechanical stability time increased, and the viscosity
remained almost constant. The tensile strength increased
during storage for a period of 20 days. The degree of
crosslinking, modulus, elongation at break, and chloroform
number were varied with the time of storage.
Blends of chlorobutyl rubber (CIIR) with two grades of ethylene-propylene diene
monomer rubber (EPDM) were prepared and the effect of blend ratio on the cure
characteristics, hot air ageing resistance, steam ageing resistance, and mechanical
properties were evaluated. The blend of CIIR with EPDM grade 301 T showed
additive behavior and the blend with the other grade of EPDM (NDR 4640)
showed synergistic behavior.
Ethylene-propylene-diene rubber (EPDM) and isobutylene-isoprene rubber (IIR) were
compounded, precured to a low degree, and then were blended with natural rubber (NR).
The compounding ingredients for NR were then added and the final curing was done. NR/
EPDM and NR/IIR blends, prepared using this method, were found to possess much
improved mechanical properties as compared to their conventional counterparts. The optimum
precuring crosslink density that has to be given to the EPDM and IIR phases has
been determined.
A novel method of blending natural rubber with polyvinylchloride in the latex
stage was developed, Dioctyl phthalate (DOP) and Amine terminated natural rubber
(ATNR) were used as plasticisers, for improving the mechanical properties of
these blends. Properties of the latex stage blends were compared with those of
dry blends. Latex stage blends showed superior mechanical properties compared
to the blends prepared in the dry state. The ageing resistance, oil resistance and
processability were found to be improved by latex stage blending.
ABSTRACT: Linseed oil is used in the dual roles of the plasticizer and the fatty
acid component of the activator in nitrile rubber vulcanizates. The study shows
that the substitution can substantially improve the mechanical properties in
addition to other advantages such as increased cure rate, reduced leachability
and reduced compound cost.
Zinc salts of ethyl, isopropyl, and butyl xanthates are prepared
in the laboratory, and the effect of these xanthates with zinc diethyl
dithiocarbamate (ZDC) on the vulcanization of HAF-filled nitrile butadiene
rubber (NBR) compounds has been studied at different temperatures. The cure
times of these compounds have been compared with that of NBR compounds
containing TMTD/MBTS. The rubber compounds with the three xanthate
accelerators and ZDC are cured at various temperatures from 60 to 150°C.
The sheets are molded and properties such as tensile strength, tear strength,
cross-link density, elongation at break, compression set, abrasion resistance,
flex resistance, etc. have been evaluated. The properties show that zinc salt
of the xanthate/ZDC accelerator system has a positive synergistic effect on the
cure rate and mechanical properties of NBR compounds.
A series of short-isora-fiber-reinforced natural
rubber composites were prepared by the incorporation of
fibers of different lengths (6, 10, and 14 mm) at 15 phr loading
and at different concentrations (10, 20, 30, and 40 phr) with a
10 mm fiber length. Mixes were also prepared with 10 mm
long fibers treated with a 5% NaOH solution. The vulcanization
parameters, processability, and stress-strain properties
of these composites were analyzed. Properties such as tensile
strength, tear strength, and tensile modulus were found to be
at maximum for composites containing longitudinally oriented
fibers 10 mm in length. Mixes containing fiber loadings of 30 phr with bonding agent (resorcinol-formaldehyde [RF]
resin) showed mechanical properties superior to all other
composites. Scanning electron microscopy (SEM) studies
were carried out to investigate the fiber surface morphology,
fiber pullout, and fiber-rubber interface. SEM studies showed
that the bonding between the fiber and rubber was improved
with treated fibers and with the use of bonding agent.
The mechanism of devulcanization of sulfur-vulcanized natural rubber with aromatic disulfides and aliphatic
amines has been studied using 23-dimethyl-2-butene (C5H1,) as a low-molecular weight model compound. First C6H12
was vulcanized with a mixture of sulfur, zinc stearate and N-cyclohexyl-2-benzothiazylsulfenamide (CBS) as accelerator
at 140 °C, resulting in a mixture of addition products (C(,H 1 i-S,-C5H 1 i ). The compounds were isolated and identified
by High Performance Liquid Chromatography (HPLC) with respect to their various sulfur ranks. In it second stage, the
vulcanized products were devulcanized using the agents mentioned above at 200 °C. The kinetics and chemistry of the
breakdown of the sulfur-hridges were monitored. Both devulcanization agents decompose sulfidic vulcanization products
with sulfur ranks equal or higher than 3 quite effectively and with comparable speed. Di phenyldisulfide as devulcanization
agent gives rise to a high amount of mono- and disulfidic compounds formed during the devulcanization,
hexadecylamine, as devulcanization agent, prevents these lower sulfur ranks from being formed.
Natural rubber, styrene-butadiene rubber, and polybutadiene
rubber were used to replace part of the butadieneacrylonitrile
rubber in a 70/30 butadiene-acrylonitrile rubber/
poly(vinyl chloride) blend. Such replacement up to 15%
of the total weight of the blend improved the mechanical
properties, while decreasing the cost of the blend. Styrenebutadiene
rubber could replace butadiene-acrylonitrile
rubber up to 30% of the total weight of the blend without
deterioration in the mechanical properties.
Rani, Joseph(Gordon and Breach Science Publishers, Inc., May 20, 1985)
[+]
[-]
Abstract:
Polychloroprene (neoprene) has been blended with polyvinylchloride (PVC) in different
proportions using a new stabiliser system (magnesium oxide and zinc oxide with
stearic acid) for PVC. The physical properties of the blends show that they can
advantageously replace neoprene in many applications.