Abstract: | Glass fiber reinforced polymer (GFRP) rebars have been identified as an alternate construction material for reinforcing concrete during the last decade primarily due to its strength and durability related characteristics. These materials have strength higher than steel, but exhibit linear stress–strain response up to failure. Furthermore, the modulus of elasticity of GFRP is significantly lower than that of steel. This reduced stiffness often controls the design of the GFRP reinforced concrete elements. In the present investigation, GFRP reinforced beams designed based on limit state principles have been examined to understand their strength and serviceability performance. A block type rotation failure was observed for GFRP reinforced beams, while flexural failure was observed in geometrically similar control beams reinforced with steel rebars. An analytical model has been proposed for strength assessment accounting for the failure pattern observed for GFRP reinforced beams. The serviceability criteria for design of GFRP reinforced beams appear to be governed by maximum crack width. An empirical model has been proposed for predicting the maximum width of the cracks. Deflection of these GFRP rebar reinforced beams has been predicted using an earlier model available in the literature. The results predicted by the analytical model compare well with the experimental data |
Description: | Construction and Building Materials 21 (2007) 1709–1719 |
URI: | http://dyuthi.cusat.ac.in/purl/4539 |
Files | Size |
---|---|
Strength and se ... h GFRP bars in flexure.pdf | (372.3Kb) |
Abstract: | Hat Stiffened Plates are used in composite ships and are gaining popularity in metallic ship construction due to its high strength-to-weight ratio. Light weight structures will result in greater payload, higher speeds, reduced fuel consumption and environmental emissions. Numerical Investigations have been carried out using the commercial Finite Element software ANSYS 12 to substantiate the high strength-to-weight ratio of Hat Stiffened Plates over other open section stiffeners which are commonly used in ship building. Analysis of stiffened plate has always been a matter of concern for the structural engineers since it has been rather difficult to quantify the actual load sharing between stiffeners and plating. Finite Element Method has been accepted as an efficient tool for the analysis of stiffened plated structure. Best results using the Finite Element Method for the analysis of thin plated structures are obtained when both the stiffeners and the plate are modeled using thin plate elements having six degrees of freedom per node. However, one serious problem encountered with this design and analysis process is that the generation of the finite element models for a complex configuration is time consuming and laborious. In order to overcome these difficulties two different methods viz., Orthotropic Plate Model and Superelement for Hat Stiffened Plate have been suggested in the present work. In the Orthotropic Plate Model geometric orthotropy is converted to material orthotropy i.e., the stiffeners are smeared and they vanish from the field of analysis and the structure can be analysed using any commercial Finite Element software which has orthotropic elements in its element library. The Orthotropic Plate Model developed has predicted deflection, stress and linear buckling load with sufficiently good accuracy in the case of all four edges simply supported boundary condition. Whereas, in the case of two edges fixed and other two edges simply supported boundary condition even though the stress has been predicted with good accuracy there has been large variation in the deflection predicted. This variation in the deflection predicted is because, for the Orthotropic Plate Model the rigidity is uniform throughout the plate whereas in the actual Hat Stiffened Plate the rigidity along the line of attachment of the stiffeners to the plate is large as compared to the unsupported portion of the plate. The Superelement technique is a method of treating a portion of the structure as if it were a single element even though it is made up of many individual elements. The Superelement has predicted the deflection and in-plane stress of Hat Stiffened Plate with sufficiently good accuracy for different boundary conditions. Formulation of Superelement for composite Hat Stiffened Plate has also been presented in the thesis. The capability of Orthotropic Plate Model and Superelement to handle typical boundary conditions and characteristic loads in a ship structure has been demonstrated through numerical investigations. |
Description: | Study about Hat Stiffened Plate |
URI: | http://dyuthi.cusat.ac.in/purl/5038 |
Files | Size |
---|---|
Dyuthi-T2103 .pdf | (2.669Mb) |
Abstract: | The focus of this study is the stress of women entrepreneurs.As stress is associated with constraints and demands, and as a set of emerging conditions seem to affect the quality of life of women, it is more than just an occasional need to enquire in to the possibilities of promoting entrepreneurship by empowering women.As women entrepreneurs are increasingly involved in inherently complicated activities of improving their enterprise functioning ,it would be appropriate for women entrepreneurs to focus on transformational coping interventions.The study is limited to women entrepreneurs in the tiny sector.Women entrepreneurs registered in the Distric Industries ( DIC) and in the Kerala State Women’s Industries Association (KSWIA) are only selected for the study.It gaves a detailed description about empowerment of women.The social , economic ,political,ecological,and psychological importance of the study are detailed.It explains the family related stress, and the contextual system.This study is suggested on beliefs and values of women about their self-perception influencing gender bias, which contribute to stress and coping.This study is also needed about women’s believes and expectations about the probable effectiveness of various course of action and their ability to perform those actions.It is also neede for appraising coping potential of women and enhancing their stress base.It is important to research on stress and self-concept |
URI: | http://dyuthi.cusat.ac.in/purl/56 |
Files | Size |
---|---|
Dyuthi-T0085.pdf | (8.837Mb) |
Abstract: | The stress relaxation behavior of polyurethane elastomer and short polyester fiber filled elastomer composites with and without bonding agents at different strain levels and strain rates was studied. It was found that these compounds exhibit a multistage relaxation mechanism and that the rate of relaxation and cross-over time depend on the strain level and strain rate. The incorporation of fibers reduced the stage-I relaxation rate and increased the cross-over time of the gum vulcanisate. A higher rate of relaxation (first stage) was shown by the composites with longitudinal fiber orientation and composites with bonding agents. |
URI: | http://dyuthi.cusat.ac.in/purl/904 |
Files | Size |
---|---|
Suhara, F S K N ... lyester fibre..........PDF | (5.093Mb) |
Abstract: | Poisoning by pesticides from agricultural fields is a serious water pollution problem and its environmental long-term effect may result in the incidence of poisoning of fish and other aquatic life forms (jyothi and Narayan, 1999). Fishes like Heteropneustesfbssilis and C/arius batrac/nus are especially prone to serious pesticide pollution as their habitat is mostly the agriculture area. Though only few studies are conducted in this area, it can be assessed from the local information that, population of such fish is on the verge of vulnerability due to extensive use of pesticides. The knowledge of sublethal effects of xenobiotic compounds on hematological parameters, enzyme activities and metabolite concentrations is very important to delineate the fish health status and provide a future understanding of ecological impacts. These pesticides act by causing inhibition of cholinesterase enzymes (ChE) by formation of enzyme inhibitor complex (O'Brien, 1976) and damaging the nervous system. These effects may result in metabolic disorders. Associated to cholinesterase activities, a study of other enzymes such as phosphatases and aminotransferases close to intermediary metabolite determination provides a wider view of metabolism. Interest in toxicological aspects has grown in recent years and research is now increasingly focused on mechanistic aspects of oxidative damage and cellular responses in biological system. The term ‘biomarker’ is generally used in a broad sense to include almost any measurement reflecting an interaction between a biological system and a potential hazard, which may be chemical, physical or biological (WHO, 1993). As biomarker stands for immediate responses, they are used as early warning signals of biological effects caused by environmental pollutants. The present work attempts to assess the toxicity of organophosphorus insecticide monocrotophos on the experimental organism selected for this study namely stinging catfish (Heteropneustesfossi/is) (Bloch), and to probe into the stress responses of the organism |
Description: | Department of Marine Biology, Microbiology and Biochemistry, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/3669 |
Files | Size |
---|---|
Dyuthi-T1564.pdf | (6.693Mb) |
URI: | http://dyuthi.cusat.ac.in/purl/5207 |
Files | Size |
---|---|
Dyuthi T-2242.pdf | (4.038Mb) |
Abstract: | For establishing nitrification in prawn (non-penaeid, salinity 10–15 ppt) and shrimp (penaeid, salinity 30–35 ppt) larval production systems, a stringed bed suspended bioreactor (SBSBR) was designed, fabricated, and validated. It was fabricated with 5 mm polystyrene and low density polyethylene beads as the substrata for ammonia and nitrite oxidizing bacterial consortia, respectively, with an overall surface area of 684 cm2. The reactors were activated in a prototype activator and were transported in polythene bags to the site of testing. Performance of the reactors activated with the nitrifying bacterial consortia AMONPCU-1 (ammonia oxidizers for non-penaeid culture) and NIONPCU-1 (nitrite oxidizers for non-penaeid culture) was evaluated in a Macrobrachium rosenbergii larval rearing system and those activated with AMOPCU-1 (ammonia oxidizers for penaeid culture) and NIOPCU-1 (nitrite oxidizers for penaeid culture) in a Penaeus monodon seed production system. Rapid setting up of nitrification could be observed in both the static systems which resulted in a higher relative per cent survival of larvae |
Description: | Aquacult Int (2009) 17:479–489 DOI 10.1007/s10499-008-9218-2 |
URI: | http://dyuthi.cusat.ac.in/purl/4068 |
Files | Size |
---|---|
Stringed bed su ... naeid hatchery systems.pdf | (347.8Kb) |
Abstract: | Design and development of a new feed -horn antenna with low sidelobe levels is reported . The E-walls of this antenna are fabricated with low -loss dielectric substrate , periodically loaded with thin conducting strips . The antenna is found to be simulating the radiation characteristics of metallic corrugated horns . This can be an ideal substitute for metallic corrugated horns with added advantages like light -weight and low production cost. |
URI: | http://dyuthi.cusat.ac.in/jspui/handle/dyuthi/1563 |
Files | Size |
---|---|
A Strip-Loaded Feed-Horn Antenna.PDF | (988.8Kb) |
Abstract: | Design and development of a new feed -horn antenna with low sidelobe levels is reported . The E-walls of this antenna are fabricated with low -loss dielectric substrate , periodically loaded with thin conducting strips . The antenna is found to be simulating the radiation characteristics of metallic corrugated horns . This can be an ideal substitute for metallic corrugated horns with added advantages like light -weight and low production cost. |
URI: | http://dyuthi.cusat.ac.in/jspui/handle/dyuthi/1562 |
Files | Size |
---|---|
A Strip-Loaded Feed-Horn Antenna.PDF | (988.8Kb) |
Abstract: | Design and development of a new feed -horn antenna with low sidelobe levels is reported . The E-walls of this antenna are fabricated with low -loss dielectric substrate , periodicallyloaded with thin conducting strips . The antenna is found to be simulating the radiation characteristics of metallic Corrugated horns . This can be an ideal substitute for metallic Corrugated horns with added advantages like light -weight and low production cost |
URI: | http://dyuthi.cusat.ac.in/purl/1361 |
Files | Size |
---|---|
A Strip-Loaded Feed-Horn Antenna.PDF | (988.8Kb) |
Abstract: | The radiation characteristics of a new type of hollow dielectric H-plane sectoral horn antenna are presented. Metallic strips of optimum length are loaded on the H-walls of the sectoral horns. The effects of strip loading for producing square patterns in the H plane are discussed. |
URI: | http://dyuthi.cusat.ac.in/purl/2977 |
Files | Size |
---|---|
Dyuthi-P00412.pdf | (115.5Kb) |
Abstract: | hindi |
Description: | Department of Hindi Cochin University of Science & Technology |
URI: | http://dyuthi.cusat.ac.in/purl/4820 |
Files | Size |
---|---|
Dyuthi-T1917.pdf | (4.991Mb) |
Abstract: | A graph G is strongly distance-balanced if for every edge uv of G and every i 0 the number of vertices x with d.x; u/ D d.x; v/ 1 D i equals the number of vertices y with d.y; v/ D d.y; u/ 1 D i. It is proved that the strong product of graphs is strongly distance-balanced if and only if both factors are strongly distance-balanced. It is also proved that connected components of the direct product of two bipartite graphs are strongly distancebalanced if and only if both factors are strongly distance-balanced. Additionally, a new characterization of distance-balanced graphs and an algorithm of time complexity O.mn/ for their recognition, wheremis the number of edges and n the number of vertices of the graph in question, are given |
Description: | European Journal of Combinatorics 30 (2009) 1048- 1053 |
URI: | http://dyuthi.cusat.ac.in/purl/4198 |
Files | Size |
---|---|
Strongly distan ... phs and graph products.pdf | (373.0Kb) |
Description: | Department of Applied Chemistry, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2186 |
Files | Size |
---|---|
Dyuthi-T0536.pdf | (5.920Mb) |
Abstract: | Rice husk silica was utilized as the promoter of ceria for preparing supported vanadia catalysts. Effect of vanadium content was investigated with 2–10 wt.% V2O5 loading over the support. Structural characterization of the catalysts was done by various techniques like energy dispersive X-ray (EDX), X-ray diffraction (XRD), BET surface area, thermal analysis (TGA/DTA), FT-infrared spectroscopy (FT-IR), UV–vis diffused reflectance spectroscopy (DR UV–vis), electron paramagnetic spectroscopy (EPR) and solid state magnetic resonance spectroscopies (29Si and 51V MASNMR). Catalytic activity was studied towards liquid-phase oxidation of benzene. Surface area of ceria enhanced upon rice husk silica promotion, thus makes dispersion of the active sites of vanadia easier. Highly dispersed vanadia was found for low V2O5 loading and formation of cerium orthovanadate (CeVO4) occurs as the loading increases. Spectroscopic investigation clearly confirms the formation of CeVO4 phase at higher loadings of V2O5. The oxidation activity increases with vanadia loading up to 8 wt.% V2O5, and further increase reduces the conversion rate. Selective formation of phenol can be attributed to the presence of highly dispersed active sites of vanadia over the support. |
URI: | http://dyuthi.cusat.ac.in/purl/2262 |
Files | Size |
---|---|
Dyuthi-SS54.pdf | (343.4Kb) |
Abstract: | Polyaniline and oligomeric cobalt phthalocyanine are blended in different proportions by chemical methods. These blends are characterised by spectroscopic methods and dielectric measurements. Dielectric studies on the conducting polymer blends are carried out in the frequency range of 100 kHz to 5MHz from room temperature (300 K) to 373 K. Dielectric permittivity and dielectric loss of these blends are explained on the basis of interfacial polarisation. From the dielectric permittivity studies, ac conductivity of the samples were calculated and the results are correlated. In order to understand the exact conduction mechanism of the samples, dc electrical conductivity of the blends is carried out in the temperature range of 70–300 K. By applying Mott’s theory, it is found that the conducting polymer composites obey a 3D variable range hopping mechanism. The values of Mott’s temperature (T0), density of states at the Fermi energy (N(EF)), range of hopping (R) and hopping energy (W) for the composites are calculated and presented |
Description: | Materials Science and Engineering B 135 (2006) 113–119 |
URI: | http://dyuthi.cusat.ac.in/purl/4373 |
Files | Size |
---|---|
Structural and ... polyaniline composites.pdf | (972.1Kb) |
Abstract: | The study deals with structural and spectral investigations of transition metal complexes of di-2-pyridyl ketone N(4),N(4)-disubstituted thiosemicarbazones. The main objective and scope of the work deals with di-2-pyridyl ketone N(4),N(4)-disubstituted thiosemicarbazones are quardridentate NNNS donor ligands. To chosen this ligand for study because, the ligands are prepared and characterized for the first time, since there are two pyridyl nitorgens, dimmers and polymers of complexes may result leading to interesting structural aspects. The work includes the preparation of the thiosemicarbzones and their structural and spectral studies, synthesis and spectral characterization of complexes of copper(II),,nickel(II),manganese(II), dioxovanadium(V),cobalt(III),zinc(II),cadmium(II) of the ligand HL, synthesis and spectral characterization of complexes of copper(II),manganese(II), of the ligand HL and the development of X-ray quality crystals and its X-ray diffraction studies. The structural characterization techniques are elemental analysis, conductivity measurements, magnetic measurements, electronic spectroscopy, H NMR spectroscopy, Infrared spectroscopy and X-ray crystallography. |
URI: | http://dyuthi.cusat.ac.in/purl/773 |
Files | Size |
---|---|
Dyuthi-T0088.pdf | (7.620Mb) |
Abstract: | Seven bis(ligand) Co(III) complexes {[CoL21] NO3 · H2 O (1), [CoL21] Cl · 2 H2 O (2),[CoL21] ClO4 (3), [CoL22] NO3 (4), [CoL22] Cl · 2 H2 O (5), [CoL23] Br · 2 H2 O (6), [CoL23] ClO4 · H2 O (7)} of three thiosemicarbazone ligands {pyridine-2-carbaldehyde-N(4)-p-methoxyphenyl thiosemicarbazone [HL1], pyridine-2-carbaldehyde-N(4)-2-phenylethyl thiosemicarbazone [HL2] and pyridine-2-carbaldehyde-N(4)-(methyl),N(4)-(phenyl) thiosemicarbazone [HL3]} were synthesized and physico-chemically characterized. All complexes are assigned octahedral geometries on the basis of spectral studies. The ligands deprotonate and coordinate by means of pyridine nitrogen, azomethine nitrogen, and thiolate sulfur atoms. The single crystal X-ray structures of HL3 and two nitrate compounds are discussed. The structural studies corroborate the spectral characterization. |
URI: | http://dyuthi.cusat.ac.in/xmlui/purl/2100 |
Files | Size |
---|---|
Structural and ... es of novel Co(III)....pdf | (772.7Kb) |
Abstract: | ZnO thin films were coated on amorphous glass substrate at various temperatures in the range 160-500 0C by spray pyrolysis method. The as deposited films were characterised by using XRD and SEM. Wurtzite phase of ZnO was formed at a substrate temperature of 400 0C, highly oriented (002) phase was developed with respect to increase of substrate temperature from 450 to 500 0C. Morphological and growth mode of these films were analyzed with respect to structural orientation of films from wurtzite to highly (002) oriented phase. Present study reveals that substrate temperature was one of the important parameters which determine the crystalline quality, population of defects, grain size, orientation and morphology of the films |
Description: | Journal of Optoelectronics and Biomedical Materials Vol. 5 Issue 1, January - March 2013 p. 1 - 8 |
URI: | http://dyuthi.cusat.ac.in/purl/4562 |
Files | Size |
---|---|
Structural And ... Spray Pyrolysis Method.pdf | (1.201Mb) |
Abstract: | The present work deals with the complexation of Schiff bases of aroylhydrazines with various transition metal ions. The hydrazone systems selected for study have long 7I:-delocalized chain in the ligand molecule itself, which get intensified due to metal-to-ligand or ligand-to-metal charge transfer excitations upon coordination. Complexation with metal ions like copper, nickel, cobalt, manganese, iron, zinc and cadmium are tried. Various spectral techniques are employed for characterization. The structures of some complexes have been well established by single crystal X-ray diffraction studies. The nonIinaer optical studies of the ligands and complexes synthesized have been studied by hyper-Rayleigh scattering technique.The work is presented in seven chapters and the last one deals with summary and conclusion. One of the hydrazone system selected for study proved that it could give rise to polymeric metal complexes. Some of the copper, nickel, zinc and cadmium complexes showed non-linear optical activity. The NLO studies of manganese and iron showed negative result, may be due to the inversion centre of symmetry within the molecular lattice. |
Description: | Department of Applied Chemistry, Cochin University of Science and Technology |
URI: | http://dyuthi.cusat.ac.in/purl/2798 |
Files | Size |
---|---|
Dyuthi-T0819.pdf | (14.44Mb) |
Dyuthi Digital Repository Copyright © 2007-2011 Cochin University of Science and Technology. Items in Dyuthi are protected by copyright, with all rights reserved, unless otherwise indicated.